Pelican 1600TP Case with TrekPak Divider System (Black)
Pelican™ Protector Case™
Sensitive equipment needs protection, and since 1976 the answer has been the Pelican™ Protector Case. These cases are designed rugged, and travel the harshest environments on earth. Against the extreme cold of the arctic or the heat of battle, Pelican cases have survived.
Made in the USA, these tough cases are designed with an automatic purge valve, that equalizes air pressure, a watertight silicone O-ring lid, over-molded rubber handles and stainless steel hardware.
Pick N Pluck™ with convoluted lid foam
Watertight, crushproof, and dustproof
Open cell core with solid wall design - strong, light weight
Automatic Pressure Equalization Valve - balances interior pressure, keeps water out
O-ring seal
Stainless steel hardware
Lifetime Guarantee of Excellence
The Pelican 1600TP Case with TrekPak Divider System (Black) is an unbreakable, watertight, airtight, dustproof, chemical resistant and corrosion proof hard case used to carry any kind of equipment that needs protection. It is made of Ultra-high Impact structural copolymer that makes it extremely strong and durable. It has a 0.25" (6.4 mm) neoprene o-ring, 4 easy-open double throw latches that seal perfectly. It has a built-in automatic pressure equalization valve for changes in altitude or temperature. The case uses stainless steel hardware and has padlock protectors to provide added strength and extra security against cutting and theft. It is carried by a comfortable rubber over-molded handle.
Besides being lighter than traditional padded dividers, the TrekPak Divider System and uses pre-installed wall sections, divider panels, locking pins, and an easy-to-use cutting tool. Simply lay your gear in the case, measure and cut the divider sections, and lock them in place with the steel U-pins. Extra divider material is included for occasions where your equipment requirements vary. 7/16" thick divider sections are made of waterproof, closed cell foam that is laminated to a rigid, corrugated plastic panel that resists tearing and shredding. The TrekPak is combined with 1" bottom foam and lid foam to give your gear 360-degree protection.
Construction
Ultra-high Impact structural copolymer
Open-cell core with solid wall design
Easy open double throw latches
Built-in automatic pressure equalization valve
Padlock protectors
Stainless steel hardware
TrekPak insert with two perimeter pieces, two 9" dividers, two 23" divider, cutter tool, 30 pins with 30 red pull tabs, plus a top and bottom foam piece.
Temperature rating -10 to +210° F (-23 to +99° C)
Comfortable rubber over-molded handle
1600 Case Certificates
IP67 (1 meter submersion for 30 minutes) (Ingress Protection)
Def Stan 81-41/STANAG 4280
Key Features
Watertight, Dustproof Case
Made of Ultra-High Impact Copolymer
TrekPak Divider System
Automatic Pressure Equalization Valve
Easy Open Double Throw Latches
Rubber Over-Molded Handle
Lifetime Guarantee of Excellence
Dimensions
Interior (L×W×D)
21.51 x 16.54 x 7.99 in (54.6 x 42 x 20.3 cm)
Exterior (L×W×D)
24.39 x 19.36 x 8.79 in (62 x 49.2 x 22.3 cm)
Pelican 1600TP,WL/TP INSERT,BLACK
Pelican™ Protector Case™
Sensitive equipment needs protection, and since 1976 the answer has been the Pelican™ Protector Case. These cases are designed rugged, and travel the harshest environments on earth. Against the extreme cold of the arctic or the heat of battle, Pelican cases have survived.
Made in the USA, these tough cases are designed with an automatic purge valve, that equalizes air pressure, a watertight silicone O-ring lid, over-molded rubber handles and stainless steel hardware.
Pick N Pluck™ with convoluted lid foam
Watertight, crushproof, and dustproof
Open cell core with solid wall design - strong, light weight
Automatic Pressure Equalization Valve - balances interior pressure, keeps water out
O-ring seal
Stainless steel hardware
Lifetime Guarantee of Excellence
The Pelican 1600TP Case with TrekPak Divider System (Black) is an unbreakable, watertight, airtight, dustproof, chemical resistant and corrosion proof hard case used to carry any kind of equipment that needs protection. It is made of Ultra-high Impact structural copolymer that makes it extremely strong and durable. It has a 0.25" (6.4 mm) neoprene o-ring, 4 easy-open double throw latches that seal perfectly. It has a built-in automatic pressure equalization valve for changes in altitude or temperature. The case uses stainless steel hardware and has padlock protectors to provide added strength and extra security against cutting and theft. It is carried by a comfortable rubber over-molded handle.
Besides being lighter than traditional padded dividers, the TrekPak Divider System and uses pre-installed wall sections, divider panels, locking pins, and an easy-to-use cutting tool. Simply lay your gear in the case, measure and cut the divider sections, and lock them in place with the steel U-pins. Extra divider material is included for occasions where your equipment requirements vary. 7/16" thick divider sections are made of waterproof, closed cell foam that is laminated to a rigid, corrugated plastic panel that resists tearing and shredding. The TrekPak is combined with 1" bottom foam and lid foam to give your gear 360-degree protection.
Construction
Ultra-high Impact structural copolymer
Open-cell core with solid wall design
Easy open double throw latches
Built-in automatic pressure equalization valve
Padlock protectors
Stainless steel hardware
TrekPak insert with two perimeter pieces, two 9" dividers, two 23" divider, cutter tool, 30 pins with 30 red pull tabs, plus a top and bottom foam piece.
Temperature rating -10 to +210° F (-23 to +99° C)
Comfortable rubber over-molded handle
1600 Case Certificates
IP67 (1 meter submersion for 30 minutes) (Ingress Protection)
Def Stan 81-41/STANAG 4280
Key Features
Watertight, Dustproof Case
Made of Ultra-High Impact Copolymer
TrekPak Divider System
Automatic Pressure Equalization Valve
Easy Open Double Throw Latches
Rubber Over-Molded Handle
Lifetime Guarantee of Excellence
Dimensions
Interior (L×W×D)
21.51 x 16.54 x 7.99 in (54.6 x 42 x 20.3 cm)
Exterior (L×W×D)
24.39 x 19.36 x 8.79 in (62 x 49.2 x 22.3 cm)
Pelican 1600TP,WL/TP INSERT,BLACK
Pelican™ Protector Case™
Sensitive equipment needs protection, and since 1976 the answer has been the Pelican™ Protector Case. These cases are designed rugged, and travel the harshest environments on earth. Against the extreme cold of the arctic or the heat of battle, Pelican cases have survived.
Made in the USA, these tough cases are designed with an automatic purge valve, that equalizes air pressure, a watertight silicone O-ring lid, over-molded rubber handles and stainless steel hardware.
Pick N Pluck™ with convoluted lid foam
Watertight, crushproof, and dustproof
Open cell core with solid wall design - strong, light weight
Automatic Pressure Equalization Valve - balances interior pressure, keeps water out
O-ring seal
Stainless steel hardware
Lifetime Guarantee of Excellence
The Pelican 1600TP Case with TrekPak Divider System (Black) is an unbreakable, watertight, airtight, dustproof, chemical resistant and corrosion proof hard case used to carry any kind of equipment that needs protection. It is made of Ultra-high Impact structural copolymer that makes it extremely strong and durable. It has a 0.25" (6.4 mm) neoprene o-ring, 4 easy-open double throw latches that seal perfectly. It has a built-in automatic pressure equalization valve for changes in altitude or temperature. The case uses stainless steel hardware and has padlock protectors to provide added strength and extra security against cutting and theft. It is carried by a comfortable rubber over-molded handle.
Besides being lighter than traditional padded dividers, the TrekPak Divider System and uses pre-installed wall sections, divider panels, locking pins, and an easy-to-use cutting tool. Simply lay your gear in the case, measure and cut the divider sections, and lock them in place with the steel U-pins. Extra divider material is included for occasions where your equipment requirements vary. 7/16" thick divider sections are made of waterproof, closed cell foam that is laminated to a rigid, corrugated plastic panel that resists tearing and shredding. The TrekPak is combined with 1" bottom foam and lid foam to give your gear 360-degree protection.
Construction
Ultra-high Impact structural copolymer
Open-cell core with solid wall design
Easy open double throw latches
Built-in automatic pressure equalization valve
Padlock protectors
Stainless steel hardware
TrekPak insert with two perimeter pieces, two 9" dividers, two 23" divider, cutter tool, 30 pins with 30 red pull tabs, plus a top and bottom foam piece.
Temperature rating -10 to +210° F (-23 to +99° C)
Comfortable rubber over-molded handle
1600 Case Certificates
IP67 (1 meter submersion for 30 minutes) (Ingress Protection)
Def Stan 81-41/STANAG 4280
Key Features
Watertight, Dustproof Case
Made of Ultra-High Impact Copolymer
TrekPak Divider System
Automatic Pressure Equalization Valve
Easy Open Double Throw Latches
Rubber Over-Molded Handle
Lifetime Guarantee of Excellence
Dimensions
Interior (L×W×D)
21.51 x 16.54 x 7.99 in (54.6 x 42 x 20.3 cm)
Exterior (L×W×D)
24.39 x 19.36 x 8.79 in (62 x 49.2 x 22.3 cm)
Pelican 1600TP,WL/TP INSERT,BLACK